TorqueSettings. Download the relevant PDF document to get instructions and torque settings. DAIHATSU DL/DG - 1001 1001. FORD/MAZDA WEC - 1005 1193. FORD/MAZDA WL/WLT - 1005 1024, 1105 1077. FORD/MAZDA FE/F8 - 1005 1022, 1105 1257. FORD/MAZDA G5/G6 - 1005 1023. FORD/MAZDA SL/SLT - 1005 1092. The2.0 duratec is a very very near square setup which is optimal for a forced induction setup. Whereas the 2.3 (and 2.5 which is even worse), is out of square, because it's a "stroker" version of the 2.0 liter, meaning the rods have to be longer, which simultaneously give those engines more power and more torque at the cost of a Weightto-torque ratio : 6.1 kg/Nm, 163.1 Nm/tonne : Engine specs; Power : 150 Hp @ 6000 rpm. Power per litre : 75 Hp/l : Torque : 190 Nm @ 4500 rpm. 140.14 lb.-ft. @ 4500 Thecylinder head bolts are torqued in four steps.1-45 ft-lbs 2-65 ft-lbs 3-65 ft-lbs 4 1/4 additional turn after reaching torque specification. On the V-6 & V-8 the connecting rod cap nuts at 45 ft-lbs and the headbolts are torqued in two steps 1-50 ft-lbs and 2-105 ft-lbs. Hope this will help you. May 16, 2010 • 1995 Dodge Dakota. TORQUEWRENCH SETTINGS. 06-2. Engine – Td4. TORQUE DESCRIPTION. METRIC. IMPERIAL. Acoustic cover to engine. 8 Nm. 6 lbf.ft. Ancillary drive belt jockey pulley Allen bolt * 24 Nm. 18 lbf.ft. Ancillary drive belt tensioner arm nut. 10 Nm. 7.5 lbf.ft. Big end bearing cap bolts: . Theone that went bang had the following numbers cast into the block: 2.0L RFCM5E-6015CA. The one I've found has the following (different) numbers: 2.0 RF4M5G-6015FF. There is also a bar-code sticker with 4 2.0 22220-09 12 04 11 47 50 printed on it. Any insights/opinions/answers would be welcomed. Itis the aim to any car tuning task to pull fuel and air into the Zetec engine. Intake Manifolds carry or channel the air from the filter and allow it to be pulled into the engine cylinders with fuel for the squish phase. Design and rate of flow of the Intake manifold can make a substantial change to fuel engine efficiency on the Zetec. Torquesettings [Manifold Bolt/fixing: Nm: ft.lb: Engine: Camshaft cover bolts: 9: 7: Camshaft gear bolt 8mm bolt 10mm bolt: 33 65: 24 48: Crankshaft pulley bolt: 205: 151: Cylinder head bolts tighten progressively 1st stage Whatis the big end bearing torque wrench settings for a ford fiesta ST150 2.0 duratec? Updated: 10/22/2022. Wiki User. ∙ 12y ago. Study now. polo torque settings 1200 engine main bearing. TORQUEWRENCH SETTINGS. 06-2. Engine – Td4. TORQUE DESCRIPTION. METRIC. IMPERIAL. Acoustic cover to engine. 8 Nm. 6 lbf.ft. Ancillary drive belt jockey pulley Allen bolt * 24 Nm. 18 lbf.ft. Ancillary drive belt tensioner arm nut. 10 Nm. 7.5 lbf.ft. Big end bearing cap bolts:

2.0 duratec engine torque settings